Mitsubishi

Mitsubishi cars are produced by Japan’s sixth largest automobile manufacturer Mitsubishi Motors Corporation. Most Mitsubishi vehicles are used in different motorsport competitions like the Dakar Rally, the World Rally Championship and the Southern Cross Rally.

Questions in Mitsubishi

Answer THE INTAKE MANIFOLD MUST BE REMOVED. I WAS QUOTED > $600 TO CHANGE PLUGS. I SOLD MINE, AS IT WAS TIME FOR A TIMING BELT AS WELL. ANOTHER $600.
Popularity: 64
Answer Hey Mary==You have to take the light assembly off by removing the screws from the back. Not an easy job sometimes. GoodluckJoe
Popularity: 58
Hey buddy I found this link, I have a 1993 4X4 Triton V6 and was asking the same question......I bought a haynes manual and found it ok, but the wiring diagrams were worthless....try this link here appears to better quality than a haynes.......http://www.vehiclemanuals.com.au/p8-mit-Triton.htm
Popularity: 112
On the inside behind the light is a bolt with a Phillips head screw, remove this. Gently push the headlight forward towards the front of the car, you may have to use a wood stick or screwdriver, gently to not mess up the paint and the light will slowly work its way forward. Reassemble by just pushin…
Popularity: 83
Answer 5 degrees before top dead center
Popularity: 71
Answer No. If you have no experience, TAKE IT TO A PROFESSIONAL. Im telling you, dont do it. You can very easily fry something in your car. Remote starts are nothing to mess around with. Remote starts are in a whole different league than putting stuff like decks, speakers, amps, whatever. Serious…
Popularity: 80
Take hold of the 2000 Mitsubishi Sport front side marker lightbulb connector. Push the connector in and turn at the same time. Do the same thing with the lightbulb. Reverse the process to install the new front side marker lightbulb.
Popularity: 31
You will need a jack & stands and properly sized ratchets/sockets (a little trial and error tends to do the trick). A wire clothes hanger, C clamp, and a small bucket also come in handy. Loosen the bolts on the wheels.Jack up the vehicle, and use stands for support.Finish removing bolts and whee…
Popularity: 40
leopen hood of vehicle. The headlamp is in a case that comes out. Headlamp screws in and out of it. Replace, and then put case back in. - Or stop at Auto Store, play dumb and have them do it for you (that's how I found out! )
Popularity: 35
Answer Did you bump something loose, and made sure you hooked everything back up?
Popularity: 34
Cam timing on 4.6 and 5.4 Ford ModularCam timing on the modular family of engines (of which the 5.4L Triton in 2-valve and 4-valve variants is a member) is built into the parts, if they're assembled correctly. The 4.6L engine found in many late 90's and newer Ford cars and trucks is also a "modular"…
Popularity: 53
Answer automatic transmission oil temperature warning light
Popularity: 59
Answer For a Galant: Open the trunk. Remove the three clips. Take off the trim cover partially. Remove the three light case mounting nuts. Push the white square grommet and remove the light case. Remove the socket assembly and bulb together by turning it counterclockwise. Take off the bulb …
Popularity: 65
another questionI have been looking for a turn signal switch and can't find one.To replace it you should just be able to take off the cover around thesteering column and snap it in where the old one was. I would be able Tobe more detailed if I could find a replacement.
Popularity: 79
Answer I have a 2000 eclipse and its under the car to the left. The oil filter is near the passenger front tire. The transmission plug is on the drivers side so they are hard to confuse.
Popularity: 68
I've played with my fruck in mud and water and when I had to take it outta 4L i made sure the truck was in neutral and that i was sititng still. Place pressure downward on the lever when shifting. Play with the car shifting from neutral to drive while rolling... it should come out
Popularity: 62
Answer You'll need an inductive timing light. Connect to the battery, and clip the induction lead over the #1 spark plug wire. Start the car. The timing mark on the crankshaft pully will appear stationary when you point the light at it, and should correspond to the timing guage(mounted on the t…
Popularity: 68
The water pump is located in the time belt compartment. It would be best not to attempt this yourself unless your an experience mechanic. If your going to have the water pump replace you should go ahead and have the timing belt and front seals replaced while they are in there. Its a major pain to d…
Popularity: 36
your vehicle needs an idle relearn needs to be done by a Mitsubishi agentmay also have a faulty stepper motor for the idle control or the battery may be losing to much voltage during start up
Popularity: 82
My wife has a 2003 Mitsubishi Diamante and I have to say that it is BY FAR the WORST car I have ever seen. The brakes seems to need service (new pads) every 5000 miles, fuel gauge has never worked correctly (we have given up and just reset the trip meter and fill up at 300 miles), have to replace t…
Popularity: 71
tpsthe TPS (throttle position sensor) is located on the throttle body. i assume you meant, 1.5 ltr Mitsubishi?? the part is normally black in colour, held on by 2 Phillips head screws or 8mm head bolts, and has a small section in it cut out, so it can be adjusted! follow the big blak tube you see un…
Popularity: 58
Look for a label on the underside of the hood, around the radiator crossover, or the compressor. The label will tell you the type and quantity of refrigerant, and also the type of refrigerant oil used in the system.
Popularity: 45
Answer I assume it is leaking or you would not be removing it. You can remove it by driving a screwdriver into the middle and prying sideways. Answer hit it on one side so that it flips sideways but hopefully not right into the cooling jacket, then grip the exposed edge and lever it out…
Popularity: 70
if some one answers this ? please send me a email with the answer. i have a 1999 Mitsubishi Diamante that when i got it had a cheap aftermarket CD player in it please send to joshatwingate@gmail.com
Popularity: 21
Answer Look all the places that sell used guns. Local gunshops, pawnshops, and sporting goods stores. Online you can try Gunbroker, GunsAmerica, Oldguns, Antiqueguns.
Popularity: 21
Answer remove the screws. make sure you dont force the dash too much, you may brake a piece or two. maybe there are covers on the screews which prevent you from seeing them.
Popularity: 79
Answer You need to get a bolt on Tophat adaptor and bolt it to the electrical box. The adaptor has a square end to bolt onto the induction box and a circular hole to accomadate the new filter. i have a 93 GLXI colt and it is a bit of work and messing about, i had alot of trouble with room beca…
Popularity: 70
Answer Try this. http://www.etrailer.com/products.asp?model=Montero&category=hitch&year=1998&make=Mitsubishi&t1=&h=e
Popularity: 60
Answer Is this vehicle all wheel drive? The vehicle is fwd so yes it can be towed with all 4 wheels on the ground.
Popularity: 71
General suggestion for heater core r&r A lot of heater cores on newer cars can be replaced from inside the engine compartment - much easier than spelunking up under the dash. Look at the firewall on the passenger side and determine where the heater hoses ( a pair of rubber hoses about 2" …
Popularity: 62
Answer No such thing as a O2 Sensor Box. The O2 sensor is located somewhere on the exhaust system. Looks similar to a spark plug with a wire connected. May be more than one. Answer The o2 sensor on my 1990 Mitsubishi Mirage 1.5L (same engine as the colt i believe) is on the exhaust betwee…
Popularity: 47
Remove axles and wheel with leverage bar. Remove caliber assembly. After removing the entire front mechanisms. Replace them with new, and reassemble tires.
Popularity: 27
Answer If you stand on the passanger side of the car, to your left will be the engine wall(between the engine and the inside of your car).There is kind of a gap. At the bottom of the wall is a rubber spigot. It is not easy to see. You can use an air compressor to blow out the clog. You may have…
Popularity: 60
inside the air filter chamber tube part,not filter part.looks like a bent wire resister inside with honeycomb behind it, DO NOT MESS WITH IT !!! VERY expensive if you bend or break it!!.just check it with a flashlight see if it is clean looking. I cannot stress enough you touch and break and part …
Popularity: 36
Answer As of today, my 2000 Galant is at 130K.
Popularity: 70
Answer You need to look down low, below the battery area. There is only a stubby round knob coming straight up from the front edge of the transmission casing itself. There is no tube coming up and extending the stick upwards, you need to reach way down low. Use a flashlight the first time if…
Popularity: 74
wire / color / polarity / location.... 12volts white + ignition harness Starter black/yellow + ignition harness Ignition black/white + ignition harness Accessory blue/black + ignition harness Second Accessory blue/white + ignition harness Notes: Not required for remote start. Keysense blue …
Popularity: 64
Answer The coil is built into the distributor. Another answer For the 1999-2003 Galant straight-four, there are two coil packs. The ignition coils go over the spark plugs for cylinders 2 and 4.
Popularity: 63
Theoretically you can supercharge any internal combustion motor. Practically, there probably is not much in the way of off-the-shelf parts available to supercharge a 2.4 litre Mitsubishi motor. In addition, the relatively small size of the motor (compared to many supercharged motors) means it would …
Popularity: 73
Answer beast way to describe it, put your front end on jack stands, crawl under on the driver side, look up and to the right. it is located behind the right wheel inside the engin compartment. You'll need to work from underneath mostly. but may fin you need to jockey it into position from the t…
Popularity: 79
Answer Are you sure it has a carburetor? Let's for sake of agruement it does, would you mean an exploded view or vacuum routing diagram or somthing else? BClear.
Popularity: 53
My girlfriends car does not have one, unless there is one built into the fuel pump in the tank. I would suggest just putting an inline filter on a fuel line under the hood, but be advised those hoses have fuel under pressure, usually there is a procedure to remove the pressure, but I dont have a man…
Popularity: 56
Answer I belong to the FTO owners club here in England. I found some information you may be looking for. http://ftooc.org/phpbb/viewtopic.php?t=18530&postdays=0&postorder=asc&start=0
Popularity: 76
Answer I just replaced the thermostat housing on my magna TR -91 model and that was on the left hand side just behind the head and underneath a whole pile of hoses- its a pig of a spot to get to - not as bad as the timing chain though.
Popularity: 68
Answer Hold the temp button down until the degree sign flashes then push the temp. button again to switch from Farenheit to Celsius.
Popularity: 56
Answer Take off the gauge cluster trim. Two screws on top, take out the hazard and other switches below the cluster to get to the two screws behind the switches, and there will be a small switch in the lower right corner, simply switch it left or right. The light will come on again at 120000,…
Popularity: 52
Answer lol u can demand a new car but ur not going to get it i wish it was that easy cause if so i would be driving me a nice brand new car to lol but no u can't get a new car all they will do is maybe total ur car and give u the blue book price and tell u to get what u can wit that and most …
Popularity: 53
Answer Did you also change out the ECU from the donor car? If not, that may be the problem.
Popularity: 56
Answer Best I have found is in the Chilton Manual 50500, Pick-ups 1983-95.
Popularity: 52
Answer It is inside the door post on the passenger's side, right near the area where the latch is. Remove the plastic trim between the passenger door and sliding door. It is a tricky one to find. I think you may need to remove the seat belt reel.
Popularity: 48
Answer Generally it is not worth the trouble to rebuild a power steering pump, especially since there are so many specialty tools involved. You can purchase a new one for far less than it would cost for you to do it properly yourself.
Popularity: 57
company called "the service center" in centurion , contact person , carel. They might beable to help . they work on Jeep, and Mitsubishi
Popularity: 67
Answer mitsubishi recommend 1000kg for a 4x2 and 1500kg for the 4x4.
Popularity: 49
Answer the TCU has gone into fail safe so you should have third and reverse you may be looking at replacing the tcu check the auto oil level then the colour (bright red ) then the fuses if both are ok then the problem is electrical pick up a second tcu from a wrecker and try that
Popularity: 56
My 1989 1.5L has the ECU behind the driver's side kick panel. I would start there. If not, it ma be behind the bottom opening of your counsol- behind shifter. Good luck my colt gti has the ecu by the passengers feet in the wing if that's any help
Popularity: 37
Answer Go to the dealership that you bought it from or look in the manual thing that you get when you bought the car.
Popularity: 21
Answer It may be a button to push or a screw to take out of one place on the back of the instrument cluster and screw it into another place on the back of the instrument cluster. Izuzu was real big on doing that back in the day.
Popularity: 40
hi bubby the order is 1-3-4-2
Popularity: 35
Answer Use the right wrenches and make sure that the radiator is cold.
Popularity: 39
Answer What is the set timing of a 1992 Mitsubishi Expo?
Popularity: 59
Where is the bottle cap type light located. If it is in the heating/AC area it most likely is telling you something is wrong with your AC pump or its running. Sounds like an A/C pump indicator light. Does your AC work? If not this is probably the reason the light is on.Hope this helps
Popularity: 21
Answer if it is a 1.7 diesel the engine code will be pn17 u can find it on a flat area on the side of motor by the gearbox
Popularity: 36
Answer I don't have it in front of me, but if you will go by a Mitsubishi dealer, they will usually look it up for you. You can also go to a Dodge dealer's service dept. The D-50 Dodge trucks were made by Mitsubishi. Most dealers will even copy it out of a service manual for you at no charge…
Popularity: 40
Intake, Exhaust, downpipe, freeflow cat/testpipe = 1200 Computer re-flash $500 intercooler $800 Turbo upgrade 1200 clutch $500 intercooler pipes $300 cams $600 That will get you the best all around performance.
Popularity: 37
I'm not sure of that models location of the the ECM, or ecu, but I'm betting it's under the passenger side seat, or located on the right side passenger kick panel, if it's under the seat, removing the seat makes it way easier, unplug the old ecm's connector(s), undo 3-4 10mm bolts that ground the ec…
Popularity: 81
Answer They should flash for a few seconds then come on permanently while in 4x4 if they continue to flash open the hood/bonnet and just behind the air filter you will see two small solenoids with vacuum pipes attached,make sure there is no leaking pipes as I cured mine yesterday with the sa…
Popularity: 43
It will not work all radio codes are different. There is a special number to call and you will need numbers off the back of radio so it will have to be removed.
Popularity: 45
Answer I am pretty sure the Expo LRV and the Eagle Summit wagon are identical. Mine has the 2.4L engine, there was also a 1.8L engine. The 2.4L version is a 4G64 type engine. There should be a metal plate on the back of the engine compartment that states the engine type. (In the center just b…
Popularity: 27
Answer Check your fuel pump relay and fuse
Popularity: 26
Answer Some do not have a filter. check with transmission shop they should be able to tell you
Popularity: 40
unbolt the old one under the rear of the van on the driver side and bolt a new one in if you can find one. good luck
Popularity: 33
Maybe due to its cramped interior, But based on its weight and dimensions , certainly not
Popularity: 24
Answer i am going on past experience here, but newer dashes(instrument panels) are all digital and just plug into a holder or wiring harness,the days of speedometer cables are basically gone forever.So,disconnect battery and find shroud screws and remove cover,then find instrument cluster screw…
Popularity: 38
Answer the price varies from shop to shop just call around and see for the best deal. Also I would recommend you going and buying the actual clutch kit yourself this way you can avoid the markup the shop will tack onto the part
Popularity: 20
Answer No. The brakes are applied manually. A brake band squeezes a brake drum.
Popularity: 25
Answer Behind the fan and gove box (passenger side). It is held in place by 1 10mm bolt. Push the carpet down a little to see the bolt. It has a couple grounding cables connected to it.
Popularity: 20
environmental control systems or  you where hacked by the matrix  Answer I think it means electronically controlled suspension.
Popularity: 24
Mitsubishi 3.0 is a interference motor Yes, 3.0 Mitsubishi is an interference motor The Mitsubishi 3.0 engine is not an interference engine , if you tear the timing belt it will not hit the valves. you can confirm this with alldata If your motor is the 12 valve motor you are safe, but the 24 valve…
Popularity: 21
I'd have to say, generally, no. It's an environmental problem that doesn't relate to the electronics or mechanical systems of the projector, which means the projector isn't defective.
Popularity: 20
Answer Airbag system is not working correctly.
Popularity: 21
The check engine light (CEL for short) is triggered when one or more of the many sensors on the vehicle detects a not-normal reading, There are 2 basic steps to determining the cause of the CEL coming on: Have the codes read - many places offer to read the engine codes for free. Autozone even provi…
Popularity: 320
There are two sets of fuses, like in most cars. The ones inside the vehicle are, as you open the driver side door, on the left of the steering wheel nearest the door. It's like a small compartment where the top comes off to reveal the fuse box area and it has a slight opening where you can pull wi…
Popularity: 30
This process is for angle heads struds ( original from Mitsu)... First initial torque must be 20Nm in alternate bolts from center to outside. follow above numbers.... 7 3 1 5 10 9 6 2 4 8 Next step is unscrew all bolts in reverse sequence. Next step is torquing again all bolts in initial sequ…
Popularity: 23
usually on a mitsubisi if you sit in the driver side just under the dash on the left hand side of the steering wheel... to see it u usually have to look directly up at from the floor of your car ;) good luck... And for everyone out there who asks if a Mitsubishi has OBDII then from what I have lear…
Popularity: 22
I'm not a mechanic, but I have a check engine light going off in my car and the mechanic I saw recently showed me a diagram. There are 2 catalytic converters, and two oxygen sensors; 1 in the engine, and one near the end of the exhaust. Hope that helps.
Popularity: 26
Engine compartment, near the battery. There are two solenoid relays mounted side by side on the front of the break master.
Popularity: 32
Replacing the fuel filter may fix the problem. Also check the air filter and replace if necessary.
Popularity: 42
For 1981 - 1982 model (may work on newer models) proceed as follows: First undo the two screws in the indicator/parking light lens and remove the lens and the body of the indicator/parking light which has the two bulbs in it. Then you will see two square plastic blocks where the screws screw into.…
Popularity: 69
Mitsubishi is the Japanese words for three diamonds. The name Mitsubishi (三菱) has two parts: "mitsu" meaning "three" and "hishi" (which becomes "bishi" in the middle of a word) meaning "water caltrop" (also called "water chestnut"), and hence "rhombus", which is reflected in the company's famous…
Popularity: 24
Yes. It is a subsidiary of Mitsubishi Heave Industries (MHI) which is a sector of Mitsubishi Corp.
Popularity: 33
What ever the thermostat is set for, probably 195 degrees.
Popularity: 65
Mit-soo-bi-shee Mit (mittens) - soo (soon) - bi (big) - she
Popularity: 41
The Stock symbol is MTU.
Popularity: 34
for motorway driving
Popularity: 63
If you have manual most likely you will have to fix the clutch. In case of automatic transmission start from checking the condition of the fluid (smell, viscosity, color). If it has to be replaced do so. You might need just add fluid, thus second step is to check the level.
Popularity: 44
The valve clearance for 4G33 engine are as follows: Intake (hot) .008 Exhaust (hot) .010
Popularity: 22
I Believe it should be stamped on the frame behind the right front wheel or Left Front wheel if your standing in front of the vehicle.
Popularity: 26